Enter Administrative User Name (24 characters max): cisco   //输入设备名称

Enter Administrative Password (24 characters max): *****     //配置管理用户和密码

Re-enter Administrative Password                 : *****

Management Interface IP Address: 172.16.34.250   // 配置管理接口 注：带内管理接口，可以通过web ssh或者telnet连接的接口，同时也是跟内网其他设备如认证服务器连接的接口

Management Interface Netmask: 255.255.255.0

Management Interface Default Router: 172.16.34.1

Management Interface VLAN Identifier (0 = untagged):

Management Interface Port Num [1 to 8]: 1

Management Interface DHCP Server IP Address: 172.16.34.1

AP Manager Interface IP Address: 172.16.34.251

AP-Manager is on Management subnet, using same values

AP Manager Interface DHCP Server (172.16.34.1):

Virtual Gateway IP Address: 1.1.1.1   //设置虚拟网关　　　为三层漫游而设置的虚拟接口，在同一个mobility group里的WLC都必须配置相同的虚拟接口

Mobility/RF Group Name: cisco   //配置Mobility/RF Group名称　用于用户在不同控制器下的AP间的三层漫游，所以不同控制器的该组必须相同

Network Name (SSID): cisco   //配置默认的SSID   LAP加入控制器时将使用它，LAP加入后WLC会把其他的SSID提供给LAP

Allow Static IP Addresses [YES][no]: yes   //客户端IP地址配置方式 yes为允许客户端使用静态IP，no则为强制客户端使用DHCP来获取IP

Configure a RADIUS Server now? [YES][no]: no 　//配置Radius server   可后期在web界面配置

Warning! The default WLAN security policy requires a RADIUS server.

Please see documentation for more details.

Enter Country Code list (enter 'help' for a list of countries) [US]: cn   //设置国家代码   CN表示中国，WLC的County Code要和AP一致，否则AP无法加入到WLC，如果存在使用不同的County Code的AP需要在WLC里面为其添加相应的国家码

Enable 802.11b Network [YES][no]: yes   //启用802.11abg

Enable 802.11a Network [YES][no]: yes

Enable 802.11g Network [YES][no]: yes

Enable Auto-RF [YES][no]: yes   //启动自动RF检测

Configure a NTP server now? [YES][no]: no   //#ntp配置

Configure the system time now? [YES][no]: no

Warning! No AP will come up unless the time is set.

Please see documentation for more details.

Configuration correct? If yes, system will save it and reset. [yes][NO]: yes #确认配置

Restoring web auth certRestoring web auth cert

Configuration saved!

Resetting system with new configuration...

Configuration saved!

Resetting system with new configuration...

//重启完成后

CISCO SYSTEMS

Embedded BIOS Version 1.0(12)12 07/23/08 10:37:30.75

Low Memory: 632 KB

High Memory: 507 MB

PCI Device Table.

Bus Dev Func VendID DevID Class              Irq

00   01   00   1022   2080   Host Bridge       

00   01   02   1022   2082   Chipset En/Decrypt 11

00   0C   00   1148   4320   Ethernet           11

00   0D   00   177D   0003   Network En/Decrypt 10

00   0F   00   1022   2090   ISA Bridge         

00   0F   02   1022   2092   IDE Controller     

00   0F   03   1022   2093   Audio              10

00   0F   04   1022   2094   Serial Bus         9

00   0F   05   1022   2095   Serial Bus         9

Evaluating BIOS Options ...

Launch BIOS Extension to setup ROMMON

Cisco Systems ROMMON Version (1.0(12)12) #0: Thu Jul 24 06:25:20 MDT 2008

Platform AIR-WLC2112-K9

Launching BootLoader...

    Cisco Bootloader (Version 4.0.191.0)

                      .o88b. d888888b .d8888.   .o88b.   .d88b.

                     d8P   Y8   `88'   88'   YP d8P   Y8 .8P   Y8.

                     8P         88    `8bo.   8P      88    88

                     8b         88      `Y8b. 8b      88    88

                     Y8b   d8   .88.   db   8D Y8b   d8 `8b   d8'

                      `Y88P' Y888888P `8888Y'   `Y88P'   `Y88P'

Booting Primary Image...

Press <ESC> now for additional boot options...

Detecting hardware . . . .

€

Cryptographic library self-test....passed!

XML config selected

Validating XML configuration

Cisco is a trademark of Cisco Systems, Inc.

Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 6.0.199.4

Initializing OS Services: ok

Initializing Serial Services: ok

Initializing Network Services: ok

Starting ARP Services: ok

Starting Trap Manager: ok

Starting Network Interface Management Services: ok

Starting System Services: ok

Starting FIPS Features: ok : Not enabled

Starting Fastpath Hardware Acceleration: ok

Starting Switching Services: ok

Starting QoS Services: ok

Starting Policy Manager: ok

Starting Data Transport Link Layer: ok

Starting Access Control List Services: ok

Starting System Interfaces: ok

Starting Client Troubleshooting Service: ok

Starting Management Frame Protection: ok

Starting Certificate Database: ok

Starting VPN Services: ok

Starting LWAPP: ok

Starting CAPWAP: ok

Starting LOCP: ok

Starting Security Services: ok

Starting Policy Manager: ok

Starting Authentication Engine: ok

Starting Mobility Management: ok

Starting Virtual AP Services: ok

Starting AireWave Director: ok

Starting Network Time Services: ok

Starting Cisco Discovery Protocol: ok

Starting Broadcast Services: ok

Starting Power Over Ethernet Services: ok

Starting Logging Services: ok

Starting DHCP Server: ok

Starting IDS Signature Manager: ok

Starting RFID Tag Tracking: ok

Starting Mesh Services:   ok

Starting TSM: ok

Starting CIDS Services: ok

Starting Ethernet-over-IP: ok

Starting DTLS server:   enabled in CAPWAP

Starting FMC HS: ok

Starting WIPS: ok

Starting SSHPM LSC PROV LIST: ok

Starting RRC Services: ok

Starting Management Services:

   Web Server: ok

   CLI: ok

   Secure Web: ok

(Cisco Controller)

Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)

User:   cisco

Password:*****

(Cisco Controller) >

二 web页面配置

浏览器输入WLC的管理接口IP地址   https://192.168.99.250

注意：是https

出现上图选择Login，然后输入账号和密码后登陆，登陆后如图